Design World

  • Home
  • Technologies
    • 3D CAD
    • Electronics • electrical
    • Fastening & Joining
    • Factory automation
    • Linear Motion
    • Motion Control
    • Test & Measurement
    • Sensors
    • Fluid power
  • Learn
    • Ebooks / Tech Tips
    • Engineering Week
    • Future of Design Engineering
    • MC² Motion Control Classrooms
    • Podcasts
    • Videos
    • Webinars
  • LEAP AWARDS
  • Leadership
    • 2022 Voting
    • 2021 Winners
  • Design Guide Library
  • Resources
    • 3D Cad Models
      • PARTsolutions
      • TraceParts
    • Digital Issues
      • Design World
      • EE World
    • Women in Engineering
  • Supplier Listings

Astrobotic to Demonstrate Asteroid and Moon Landing Technology

By atesmeh | April 5, 2013

Share

Last week Astrobotic successfully flew a sensor package designed to guide spacecraft safely to the surface of asteroids, moons, planets, and beyond. The flight occurred on an unmanned helicopter operated by a pilot on the ground. The flights are preparation for demonstration of this capability on a propulsive lander similar to Astrobotic’s Griffin.  Astrobotic was selected by NASA for flight opportunities on a propulsive lander which culminate in a fully autonomous landing demonstration with hazard detection, trajectory planning, and closed-loop control.

“This flight opportunity represents a major milestone not just for us, but for spacecraft in general. We’ll be the first to demonstrate a GPS-denied propulsive landing from high altitude that can re-plan its route after discovering its targeted landing area is unsafe to land,” said Kevin Peterson, Director of Guidance, Navigation, and Control for Astrobotic. 

The helicopter flight is one of a series of flights to occur over the next few months. These flights will verify performance of the underlying hardware and software. When the software has reached stability with predictable performance, it will be tasked to land the helicopter by itself—without GPS. Astrobotic’s landing sensor uses two cameras, an inertial measurement unit, and a scanning laser.

“The pair of cameras work together like human eyes to measure distance and track motion. The scanning laser gives precise distance measurements and enables us to pick out hazards as small as a curb. The sensor combines these sensors with an inertial measurement unit—the device that enables smartphones to switch from landscape to portrait mode– to build its models,” Peterson explained. 

The program will exhibit terrain relative navigation, which enables precise landing on planetary bodies without GPS. The spacecraft will autonomously compare imagery captured from cameras with maps from satellite imagery to determine its location. This technology will revolutionize access to planetary surfaces through a 100-fold increase in the accuracy of planetary landings.

For more information visit http://astrobotic.com.


Filed Under: Aerospace + defense

 

Related Articles Read More >

Ontic acquires Servotek and Westcon product lines from Marsh Bellofram
Flexible rotary shafts support thrust reverser on 150 LEAP 1-A turbofan engines
Drone-mounted inspection breaks barriers for F-35
TriStar, a misunderstood failure of design

DESIGN GUIDE LIBRARY

“motion

Enews Sign Up

Motion Control Classroom

Design World Digital Edition

cover

Browse the most current issue of Design World and back issues in an easy to use high quality format. Clip, share and download with the leading design engineering magazine today.

EDABoard the Forum for Electronics

Top global problem solving EE forum covering Microcontrollers, DSP, Networking, Analog and Digital Design, RF, Power Electronics, PCB Routing and much more

EDABoard: Forum for electronics

Sponsored Content

  • Global supply needs drive increased manufacturing footprint development
  • How to Increase Rotational Capacity for a Retaining Ring
  • Cordis high resolution electronic proportional pressure controls
  • WAGO’s custom designed interface wiring system making industrial applications easier
  • 10 Reasons to Specify Valve Manifolds
  • Case study: How a 3D-printed tool saved thousands of hours and dollars

Design World Podcasts

May 17, 2022
Another view on additive and the aerospace industry
See More >
Engineering Exchange

The Engineering Exchange is a global educational networking community for engineers.

Connect, share, and learn today »

Design World
  • Advertising
  • About us
  • Contact
  • Manage your Design World Subscription
  • Subscribe
  • Design World Digital Network
  • Engineering White Papers
  • LEAP AWARDS

Copyright © 2022 WTWH Media LLC. All Rights Reserved. The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of WTWH Media
Privacy Policy | Advertising | About Us

Search Design World

  • Home
  • Technologies
    • 3D CAD
    • Electronics • electrical
    • Fastening & Joining
    • Factory automation
    • Linear Motion
    • Motion Control
    • Test & Measurement
    • Sensors
    • Fluid power
  • Learn
    • Ebooks / Tech Tips
    • Engineering Week
    • Future of Design Engineering
    • MC² Motion Control Classrooms
    • Podcasts
    • Videos
    • Webinars
  • LEAP AWARDS
  • Leadership
    • 2022 Voting
    • 2021 Winners
  • Design Guide Library
  • Resources
    • 3D Cad Models
      • PARTsolutions
      • TraceParts
    • Digital Issues
      • Design World
      • EE World
    • Women in Engineering
  • Supplier Listings