Design World

  • Home
  • Technologies
    • 3D CAD
    • Electronics • electrical
    • Fastening & Joining
    • Factory automation
    • Linear Motion
    • Motion Control
    • Test & Measurement
    • Sensors
    • Fluid power
  • Learn
    • Ebooks / Tech Tips
    • Engineering Week
    • Future of Design Engineering
    • MC² Motion Control Classrooms
    • Podcasts
    • Videos
    • Webinars
  • LEAP AWARDS
  • Leadership
    • 2022 Voting
    • 2021 Winners
  • Design Guide Library
  • Resources
    • 3D Cad Models
      • PARTsolutions
      • TraceParts
    • Digital Issues
      • Design World
      • EE World
    • Women in Engineering
  • Supplier Listings

NASA sees Tropical Storm Julio as part of a heated Eastern Pacific

By atesmeh | August 6, 2014

Share

The Eastern Pacific Ocean has been warm this springtime, and those warmer waters have contributed to the development of storms like Tropical Storm Julio and Hurricane Iselle.

“Ocean temperatures in the Eastern Tropical Pacific were heated up because of the strong Kelvin wave activity this spring. Although the initial excitement of an impending El Nino has quieted down, these warmer waters have caused an early and active hurricane season,” said Bill Patzert, Climatologist at NASA’s Jet Propulsion Laboratory in Pasadena, California.

“Kelvin waves” are massive ripples in sea level that travel across the Pacific from Australia to South America. Forecasters are paying close attention because these waves could be a herald of El Niño.

“Today, two strong cyclonic systems, Iselle (a major category 4 hurricane) and weaker Julio have their sights set on the Hawaiian Islands,” Patzert said. “Hawaii is on high alert. Hurricane impacts in the Hawaiian Islands are quite unusual. Since 1950, only five hurricanes have made land-fall in the Islands. The good news is that both Iselle and Julio should weaken as they enter cooler ocean waters.”

On August 5, NOAA’s GOES-West satellite captured an image of Tropical Storm Julio and developing System 98E located near southern Mexico’s coast.

On August 5 at 11 a.m. EDT (1500 UTC) Tropical Storm Julio had maximum sustained winds near 60 mph (95 kph). The National Hurricane Center (NHC) expects Julio to become a hurricane tomorrow, Wednesday, August 6.

Julio was centered about 1,145 miles (1,845 km) west-southwest of the southern tip of Baja California, near latitude 14.0 north and longitude 124.7 west. Julio is moving toward the west near 13 mph (20 kph). NHC expects a general westward to west-northwestward motion to continue through Thursday.

To the east of Tropical Storm Julio is yet another developing area of low pressure. That area, designated as System 98E is located near 10.3 north latitude and 98.1 west longitude several hundred miles south of Acapulco, Mexico. It has a medium chance of developing into a tropical depression in the next two days.

Original Release: http://www.eurekalert.org/pub_releases/2014-08/nsfc-nst080514.php


Filed Under: Aerospace + defense

 

Related Articles Read More >

Flexible rotary shafts support thrust reverser on 150 LEAP 1-A turbofan engines
Drone-mounted inspection breaks barriers for F-35
TriStar, a misunderstood failure of design
Air Force Jet
How drones are advancing metrology for fighter jets

DESIGN GUIDE LIBRARY

“motion

Enews Sign Up

Motion Control Classroom

Design World Digital Edition

cover

Browse the most current issue of Design World and back issues in an easy to use high quality format. Clip, share and download with the leading design engineering magazine today.

EDABoard the Forum for Electronics

Top global problem solving EE forum covering Microcontrollers, DSP, Networking, Analog and Digital Design, RF, Power Electronics, PCB Routing and much more

EDABoard: Forum for electronics

Sponsored Content

  • Global supply needs drive increased manufacturing footprint development
  • How to Increase Rotational Capacity for a Retaining Ring
  • Cordis high resolution electronic proportional pressure controls
  • WAGO’s custom designed interface wiring system making industrial applications easier
  • 10 Reasons to Specify Valve Manifolds
  • Case study: How a 3D-printed tool saved thousands of hours and dollars

Design World Podcasts

May 17, 2022
Another view on additive and the aerospace industry
See More >
Engineering Exchange

The Engineering Exchange is a global educational networking community for engineers.

Connect, share, and learn today »

Design World
  • Advertising
  • About us
  • Contact
  • Manage your Design World Subscription
  • Subscribe
  • Design World Digital Network
  • Engineering White Papers
  • LEAP AWARDS

Copyright © 2022 WTWH Media LLC. All Rights Reserved. The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of WTWH Media
Privacy Policy | Advertising | About Us

Search Design World

  • Home
  • Technologies
    • 3D CAD
    • Electronics • electrical
    • Fastening & Joining
    • Factory automation
    • Linear Motion
    • Motion Control
    • Test & Measurement
    • Sensors
    • Fluid power
  • Learn
    • Ebooks / Tech Tips
    • Engineering Week
    • Future of Design Engineering
    • MC² Motion Control Classrooms
    • Podcasts
    • Videos
    • Webinars
  • LEAP AWARDS
  • Leadership
    • 2022 Voting
    • 2021 Winners
  • Design Guide Library
  • Resources
    • 3D Cad Models
      • PARTsolutions
      • TraceParts
    • Digital Issues
      • Design World
      • EE World
    • Women in Engineering
  • Supplier Listings