Design World

  • Home
  • Technologies
    • 3D CAD
    • Electronics • electrical
    • Fastening & Joining
    • Factory automation
    • Linear Motion
    • Motion Control
    • Test & Measurement
    • Sensors
    • Fluid power
  • Learn
    • Ebooks / Tech Tips
    • Engineering Week
    • Future of Design Engineering
    • MC² Motion Control Classrooms
    • Podcasts
    • Videos
    • Webinars
  • LEAP AWARDS
  • Leadership
    • 2022 Voting
    • 2021 Winners
  • Design Guide Library
  • Resources
    • 3D Cad Models
      • PARTsolutions
      • TraceParts
    • Digital Issues
      • Design World
      • EE World
    • Women in Engineering
  • Supplier Listings

TALONS Tested On Commissioned U.S. Navy Vessel For First Time

By DARPA | August 16, 2017

Share

DARPA’s Towed Airborne Lift of Naval Systems (TALONS) research effort recently demonstrated its prototype of a low-cost, elevated sensor mast aboard a commissioned U.S. Navy vessel for the first time. The crew of USS Zephyr, a 174-foot (53-meter) Cyclone-class patrol coastal ship, evaluated the technology demonstration system over three days near Naval Station Mayport, Florida.

TALONS demonstrated safe and routine operation from the ship’s deck under a variety of sea states and wind conditions without adversely affecting the ship’s operational capability. In tests, the system significantly improved the ship’s ability to detect, track, and classify contacts of interest. It also increased communications range between the ship and remote platforms such as the Zephyr’s rigid hull inflatable boats (RHIBs).

Towed behind boats or ships, TALONS could persistently suspend intelligence, surveillance, reconnaissance (ISR) instruments and communications payloads of up to 150 pounds at altitudes between 500 and 1,500 feet above sea level—many times higher than current ships’ masts—greatly extending the equipment’s range and effectiveness.

“We’re very pleased with the USS Zephyr testing, which showed that a future system based on TALONS could provide operational benefits for even small Navy vessels,” said Scott Littlefield, a program manager in DARPA’s Tactical Technology Office (TTO). “In the next year, we will continue our cooperative relationship with the U.S. Navy and work toward fully automating launch and recovery, which would make the system even easier to use on manned vessels and compatible with unmanned surface vessels.”

“Expectations were really exceeded with the ease of not only deployment, but the recovery of the system,” said Lt. Cmdr. Cameron Ingram, commanding officer of the Zephyr. “Beyond the initial launch, it immediately stabilized, and it had a very smooth transition all the way up to altitude. I was very impressed with how stable it was.”

The TALONS test on USS Zephyr built upon a successful joint test last year with DARPA’s Anti-Submarine Warfare (ASW) Continuous Trail Unmanned Vessel (ACTUV) program. ACTUV’s technology demonstration vessel set sail with TALONS as its first payload as part of open-water testing off the coast of California.

TALONS is part of DARPA’s Phase 1 research for Tern, a joint program between DARPA and the U.S. Navy’s Office of Naval Research (ONR).


Filed Under: Aerospace + defense

 

Related Articles Read More >

Ontic acquires Servotek and Westcon product lines from Marsh Bellofram
Flexible rotary shafts support thrust reverser on 150 LEAP 1-A turbofan engines
Drone-mounted inspection breaks barriers for F-35
TriStar, a misunderstood failure of design

DESIGN GUIDE LIBRARY

“motion

Enews Sign Up

Motion Control Classroom

Design World Digital Edition

cover

Browse the most current issue of Design World and back issues in an easy to use high quality format. Clip, share and download with the leading design engineering magazine today.

EDABoard the Forum for Electronics

Top global problem solving EE forum covering Microcontrollers, DSP, Networking, Analog and Digital Design, RF, Power Electronics, PCB Routing and much more

EDABoard: Forum for electronics

Sponsored Content

  • Global supply needs drive increased manufacturing footprint development
  • How to Increase Rotational Capacity for a Retaining Ring
  • Cordis high resolution electronic proportional pressure controls
  • WAGO’s custom designed interface wiring system making industrial applications easier
  • 10 Reasons to Specify Valve Manifolds
  • Case study: How a 3D-printed tool saved thousands of hours and dollars

Design World Podcasts

May 17, 2022
Another view on additive and the aerospace industry
See More >
Engineering Exchange

The Engineering Exchange is a global educational networking community for engineers.

Connect, share, and learn today »

Design World
  • Advertising
  • About us
  • Contact
  • Manage your Design World Subscription
  • Subscribe
  • Design World Digital Network
  • Engineering White Papers
  • LEAP AWARDS

Copyright © 2022 WTWH Media LLC. All Rights Reserved. The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of WTWH Media
Privacy Policy | Advertising | About Us

Search Design World

  • Home
  • Technologies
    • 3D CAD
    • Electronics • electrical
    • Fastening & Joining
    • Factory automation
    • Linear Motion
    • Motion Control
    • Test & Measurement
    • Sensors
    • Fluid power
  • Learn
    • Ebooks / Tech Tips
    • Engineering Week
    • Future of Design Engineering
    • MC² Motion Control Classrooms
    • Podcasts
    • Videos
    • Webinars
  • LEAP AWARDS
  • Leadership
    • 2022 Voting
    • 2021 Winners
  • Design Guide Library
  • Resources
    • 3D Cad Models
      • PARTsolutions
      • TraceParts
    • Digital Issues
      • Design World
      • EE World
    • Women in Engineering
  • Supplier Listings